65A-100A 165V Integrated Charger-Discharge HCF5

HCF5 series Automatic Charger/Discharger:

It is applicable to the charging and discharging of various acid and alkaline batteries and the detection of battery storage performance. It is a good choice for uninterrupted power supplies, UPS power supplies, battery users and battery manufacturers in finance, telecommunications, mobile communications, power plants, power stations, etc

Operating mode

This device could support several operating modes, including charge mode, discharge mode and circulation mode of charge and discharge. Parameters such as current, voltage and time maintained for every stage could be set according to the battery maintenance technology.

a) Charge mode

Total four charge modes could be chosen, as follows,

●Charge mode of constant current, constant voltage, low constant current (lUla);

●Charge mode of constant current, constant voltage (IUa);

●Constant current, constant voltage, float charge mode (IUUa);

●Initial charge mode (lla).

b) Discharge mode

Discharge mode would be performed through the method of constant current control. In the

discharge process, discharge current would keep constant. When discharging large-power loaded

resistor, no affection to the grid.

c) Circulation mode of charge and discharge

Circulation mode would combine together charge and discharge process, achieving the automatic transfer between these two processes. Charge & discharge cycle

times and its time intervals could be set based on the actual situation, which would provide much convenience to the maintenance of batteries.

 

Technical Feature

● Through the application of an industrial color touch screen, this device could not only display the. charge & discharge parameters, its operation status and fault information but monitor its working curve in realtime. Parameters of each point in the curve such as charge current, charge voltage, charge capacity and charge time could be readable.

● Function of automatic switch. Referring to the battery voltage, this device could automatically identify and switch the secondarytap position of main transformer and shift to the corresponding tap position of large -power-loaded resistor, achieving the function of automatic switch.

● Refering to the charge & discharge process and parameters of batteries, Users could set head of time not only corresponding charge curve, but curve parameters at

● each stage. Parameters could also be set and modified online in the charge and discharge process.This charger would complete the whole process automatically according to the selected parameters.

● The parameters set by users would be recorded persistently, The data would not be lost if and when the power is terminated.

● Phase sequence would not be required for power grid, The three phase input, A& B & C could be randomly connected.

● Function of start-up delay, soft start-up and soft shutdown.

● Fault protection functions, such as open circuit, battery reversal, overcurrent, overvoltage, overheating, lack of equal protection function and warning function.

● Pause function. This device could suspend the charge & discharge process,.After restart, this device would recover to the previous status. Make sure the charge & discharge process would continue to run.

● Reset Function. Make sure this system would back to the normal situation.

● Power failure protection function. When turned on or when the power is reset, this device would automatically recover to the previous status, achieving the goal of unmanned state guarding.

● In the charge and discharge process, this device would shut automatically if and when the battery connecting wire falls off

● Function of recording and storing charge & recharge process data and charge curve. This device could store the charge information for more than 3000 times. SD card

● Would automatically record the details of parameter changes in every charge and discharge process, Data stored in SD card could be printed out.

Main technical parameters

Type  (AIV)	Ratedlnput Pover 50HZ	Input current AC A	Chargeand discharge current DC A	Charge Voltage (V)	power Output (kw)	Battery Packs (V)	Size (mm)	Weight（Kg）
HCF5-65/165	380V 50Hz	28	3~65	12~165	10.8	12~120	900×595×1751	285
HCF5-80/165		35	4~80	12~165	13.2	12~120		330
HCF5-100/165		44	5~100	12~165	16.5	12~120		362
HCF5-65/210		34	3~65	12~210	13.7	12~144		330
HCF5-80/210		42	4~80	12~210	16.8	12~144		345
HCF5-100/210		53	5~100	12~210	21.0	12~144		390